EN
AR
FR
DE
PT
RU
ES
Glass Tempering Furance
Glass Tempering Furance Flat bend furnace
Advantages
1. Man-machine operation interface of intelligent control system
2. temperature control template accurate fine response speed fast inhibition rate is very high
3. The furnace door adopts the advanced guillotine type up and down design
4. high resistance deformation open and close freely
5. The synchronous o-belt is designed with two grooves
6. The heating section is more stable in reciprocating and online replacement is efficient and convenient
Toughened glass type
1. Ultra-white glass
2. Screen printed glass
3. Embossed glass
4. Tinted glass
5. white glass
Main parameters
|
Model |
Max loading size (mm) |
Min size (mm) |
Thickness (mm) |
Output (m²/h) |
Installed capacity (KVA) |
|
AT-TA1225 |
1250×2500 |
100×250 |
3-19 |
53 |
200 |
|
AT-TA1636 |
1600×3660 |
100×250 |
3-19 |
91 |
400 |
|
AT-TA2036 |
2000×3660 |
100×250 |
4-19 |
126 |
500 |
|
AT-TA2436 |
2440×3660 |
100×300 |
4-25 |
152 |
630 |
|
AT-TA2442 |
2440×4200 |
100×300 |
4-25 |
173 |
630 |
|
AT-TA2450 |
2440×5000 |
100×300 |
4-25 |
202 |
800 |
|
AT-TA2460 |
2440×6000 |
100×300 |
4-25 |
245 |
1000 |
|
AT-TA2842 |
2850×4200 |
200×350 |
5-25 |
213 |
800 |
|
AT-TA2850 |
2850×5000 |
200×350 |
5-25 |
247 |
1000 |
|
AT-TA2860 |
2850×6000 |
200×350 |
5-25 |
301 |
1000 |
|
AT-TA3050 |
3000×5000 |
200×400 |
5-25 |
267 |
1000 |
|
AT-TA3060 |
3000×6000 |
200×400 |
5-25 |
321 |
1250 |
|
AT-TA3350 |
3300×5000 |
200×400 |
5-25 |
300 |
1000 |
|
AT-TA3360 |
3300×6000 |
200×400 |
5-25 |
352 |
1250 |
Note: 1. The data in the table are calculated according to 5 mm white glass and 100% loading rate;The actual data varies with the glass varieties, specifications and loading conditions.
2. Other models are not listed in full
3. The company reserves the right to change relevant parameters after technical update
At-ta type glass tempered furnace is mainly used for processing glass products in building, furniture, home appliances, decoration, automobile and other industries.
At-ta type glass tempered furnace unit main production data sheet
|
Ordinary white glass |
4-6mm 1.0‰ 8-19mm 0.8‰ |
|
|
Wave bend |
Ordinary white glass |
4-6mm 0.2mm/300mm 8-19mm 0.15mm/300mm |
|
Wind Spot |
Under natural light, wind spots will not be visible if the observation distance is not less than 1000mm, the observation Angle is not less than 15°, and the thickness of the glass lamination is not more than 30mm or the thickness of the single glass is not more than 19mm. |
|
Operating points
1. It is absolutely forbidden to switch working mode in the flat-bending tempered furnace during the production process, which may lead to serious logic errors, resulting in the loss of glass state, and the glass will remain in the furnace.
2. flat bending furnace can never use the length of the glass to work at multiple stations, this may lead to the glass position in the furnace confusion, resulting in too large fluctuations in the position of the furnace, the general size control in the range of 50mm.If you choose a new specification, you must wait until all products of the previous specification are out of the oven before the next production.
3. During the maintenance of flat bend steel furnace, the equipment must be put into the standby mode of the system, so that part of the equipment can be manually controlled, but the system will not automatically run the automatic continuous operation of the production process.
Toughened furnace
4. flat bend furnace system maintenance must do a good job of safety protection, in important departments must be necessary when you can press the emergency stop button or cut off the power supply.